DDL is experienced in performing package, product and material tests that comply with the following industry standards:
| ANSI Standards | |
| ICWM-2004 | Performance Standard for Casters & Wheels |
AAMI Standards | |
Infusion Pump Performance Testing | |
| ASTM Standards | |
| Mechanical Testing of Steel Products | |
| Tension Testing of Wire Rope and Strand | |
| Shear Testing of Aluminum & Aluminum-Alloy Rivets | |
Shear Testing of Aluminum Alloys | |
| Durability Wear Testing of Separable Electrical Connector Systems | |
| Shear Properties of Sandwich Core Materials | |
| Flatwise Tensile Strength of Sandwich Constructions | |
| Water Absorption, Bulk Density, Apparent Porosity and Apparent Sp. Gravity of Fired Whiteware Products | |
| Flexural Properties of Sandwich Constructions | |
| Compressive Strength of Fired Whiteware Materials | |
| Flexural Strength of Advanced Ceramics | |
| Static Tests of Lumber in Structural Sizes | |
Vulcanized Rubber & Thermoplastic Elastomers - Tension | |
| Evaluating the Resistance of Plastics to Chemical Reagents | |
| Water Absorption of Plastics | |
| Rubber Properties in Compression | |
| Tear Strength of Vulcanized Rubber and Thermoplastic Elastomers | |
| Tensile Properties of Plastics | |
| Standard Test Method for Determination of Compressive Resistance | |
| Deflection Temperature of Plastics under Flexural Load | |
| Compressive Properties of Rigid Plastics | |
| Coefficient of Linear Thermal Expansion of Plastics | |
| Shear Strength of Plastics by Punch Tool | |
| Air Permeability of Textile Fabrics | |
| Apparent Bending Modulus of Plastics by Means of a Cantilever Beam | |
| Bursting Strength of Paper | |
| Flexural Properties of Plastics and Insulating Materials | |
| Density and Specific Gravity of Plastics | |
| Tensile Properties of Thin Plastic Sheeting | |
Test Methods for Tire Cords and Industrial Filament Yarns | |
| Tensile Properties of Adhesive Bonds | |
| Peel or Stripping Strength of Adhesive Bonds | |
| Strength of Adhesive Bonds in Shear by Compression | |
| Bond Strength of Sheet Plastics and Electrical Insulating Materials | |
| Standard Method for Vibration Testing of Shipping Containers | |
| Shear Strength of Single Lap Adhesive Bonds | |
| Initial Tear Resistance of Plastic Films | |
| Properties of Wood-Based Fiber and Particle Panels | |
| Linear Dimensional Changes Under Accelerated Aging Conditions | |
| Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test | |
| Linear Dimensional Changes of Non-rigid Thermoplastic Film at Elevated Temp | |
| Tear Resistance of Fabrics (Elmendorf Method) | |
Compressive Properties of Rigid Cellular Plastics | |
| Apparent Density of Rigid Cellular Plastics | |
Tensile and Adhesion properties of Rigid Cellular Plastics | |
| Tensile Properties of Plastics by Microtensile Specimens | |
| Mechanical Fasteners in Wood | |
| Peel Resistance of Adhesives | |
| Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | |
| Tear-Propagation Resistance (Trouser Tear) of Plastic Film | |
Tensile Strength of Adhesives by Bar and Rod Specimens | |
| Testing Structural Insulating Roof Deck | |
| Tensile Properties of Yarns | |
| Tensile Properties of Glass Fiber Strands, Yarns, and Rovings | |
| Short-Beam Strength of Polymer Matrix Composite Materials | |
| External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading | |
| Structural Panels in Planar Shear | |
| Polyethylene (PE) Plastic Tubing | |
| Pressure-Sensitive Tack of Adhesives Using an Inverted Probe Machine1 | |
| Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics | |
| Tensile Properties of Polymer Matrix Composite | |
Standard Test Method for Determination of Leaks in Flexible Packaging by Bubble Emission | |
Standard Test Method for Water Vapor Transmission of Flexible Heat-Sealed Packages for Dry Products | |
| Strength of Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading | |
Strength Properties of Adhesives in Shear by Tension – Single Lap-Shear Assemblies | |
| Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | |
| Mechanical-Shock Fragility of Products, Using Shock Machines | |
| Test Methods for Flexible Cellular Materials | |
| Vibration (Vertical Linear Motion) Test of Products | |
Accelerated Aging of Pressure Sensitive Tapes | |
| Strength and Shear Modulus of Adhesives by Tensile-Lap Specimen | |
| Standard Practice for Performance Testing of Shipping Containers and Systems | |
Standard Practice for Conditioning Containers, Packages, or Packaging Components for Testing | |
| Shear Strength of Pultruded Reinforced Plastic Rods by the Short-Beam Method | |
| Standard Test Method for Random Vibration Testing of Shipping Containers | |
Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method | |
| Breaking Strength and Elongation of Textile Fabrics | |
Breaking Force and Elongation of Textile Fabrics (Strip Method) | |
| Detection of Holes in Medical Gloves | |
Standard Test Method for Drop Test for Loaded Containers by Free Fall | |
Elongation of Narrow Elastic Fabrics | |
Standard Test Method for Simulated Drop of Loaded Containers by Shock Machines | |
| Modulus of Elasticity for Plastic Specimens by Three-Point Bending | |
| Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method | |
| Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers | |
| Tension Testing of Metallic Materials | |
Strength Testing of Building Panels | |
| Tension Testing of Metallic Foil | |
Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio by Impulse Excitation of Vibration | |
| Standard Test Method for Seal Strength of Flexible Barrier Materials | |
Elastomeric Seals (Gaskets) for Joining Plastic Pipe | |
Performance Specs for Foley Catheters | |
Bond Strength or Ply Adhesion of Similar Laminates Made from Flexible Materials | |
| Standard Test Methods for Internal Pressurization Failure Resistance of Unrestrained Packages for Medical Applications | |
| Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates | |
Oxygen Concentrators for Domiciliary Use | |
Standard Test Method for Microbial Ranking of Porous Packaging Materials (Exposure Chamber Method) | |
Determining Axial Pullout Strength of Medical Bone Screws | |
Standard Test Method for Detecting Seal Leaks in Porous Medical Packaging by Dye Penetration | |
Standard Guide for Accelerated Aging of Sterile Medical Device Packaging | |
Standard Test Method for Detecting Gross Leaks in Medical Packaging by Internal Pressurization (Bubble Test) | |
| Consumer Safety Performance Specification for Shopping Carts | |
CENELEC Standards | |
| EN 45502 | Active Implantable Medical Devices |
| EIA Standards | |
RS-186 | |
| ETS Standards | |
| 300-019 | Environmental Tests for Telecommunications Equipment |
| IEC Standards | |
| Environmental Testing Part I: General guidance | |
| Basic Environmental Testing Procedures Test N: Change of temperature | |
| Environmental Testing- Guidance on change of temperature tests | |
| Composite Temperature/Humidity Cyclic Test | |
| Vibration, broad-band random (digital control) and guidance | |
Medical Electrical Equipment – Part 1: General requirements for basic safety and essential performance | |
ISO Standards | |
Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties | |
Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment | |
| Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment -- Part 2: Lock fittings | |
| Reusable all-glass or metal-and-glass syringes for medical use -- Part 1: Dimensions | |
| Packaging -- Complete, filled transport packages and unit loads -- Vibration tests at fixed low frequency | |
Implants for surgery – Cardiac Pacemakers – Part 3: Low profile connectors (IS-1) for implantable pacemakers | |
| Sterile hypodermic needles for single use | |
| Sterile Hypodermic Syringes. Part 1: Syringes for manual use | |
Packaging -- Complete, filled transport packages and unit loads -- Sinusoidal vibration tests using a variable frequency | |
| Oxygen Concentrators for Medical Use – Safety Requirements | |
| Infusion equipment for medical use – Part 4: Infusion sets for single use, gravity feed | |
Measurement and evaluation of shock and vibration effects on sensitive equipment in buildings | |
Sterle single-use syringes, with or without needle for insulin | |
| Optics and optical instruments -- Environmental test methods -- Part 10: Combined sinusoidal vibration and dry heat or cold | |
Environmental test methods -- Part 15: Combined digitally controlled broad-band random vibration and dry heat or cold | |
| Environmental test methods -- Part 19: Temperature cycles combined with sinusoidal or random vibration | |
| Stainless steel needle tubing for manufacture of medical devices | |
| Single Use Sterile Rubber Gloves | |
| Sterile, single-use intravascular catheters – general requirements | |
| Sterile, single-use intravascular catheters – Central venous catheters | |
| Sterile, single-use intravascular catheters – Over-needle peripheral catheters | |
| Measurement of vibro-acoustic transfer properties of resilient elements | |
| Sterile Single-use Intravascular Catheter Introducers | |
ISTA Standards | |
| Pre-Shipment Test Procedure | |
| JIS Standards | |
C0040 | |
| C0041 | Environmental Tests – Shock and Vibration |
| MIL Standards | |
| 167 | Vibration Testing |
| 202 | Electronic and Electrical Component Parts |
| 810F | Test Method Standard for Environmental Engineering Considerations and Laboratory Tests |
| 883 | |
| HDBK-17 | Composite Materials |
| P-26514 | Polyurethane Foam, Rigid or Flexible, for Packaging |
NAVMAT Standards | |
| P-9492 | Temperature Cycling and Random Vibration |
| NEMA | |
| High Pressure Laminates | |
| PDA Technical Reports | |
| Tech. Report #27 | Pharmaceutical Package Integrity, 1998 Supplement, Vol. 52 , No: 52 |
| Tech. Report #39 | Cold Chain Guidance for Medicinal Products: Maintaining the Quality of Temperature-Sensitive Medicinal Products Through The Transportation Environment, Sept/Oct 2005, Supplement, Vol. 59, No: S-3 |
SAE Standards | |
| Environmental Practices for Electronic Equipment Design | |
JEDEC Standards | |
| JESD22-A104-B | Temperature Cycling for Electronic Circuits |
| Accelerated Moisture Resistance for Electronic Circuits | |
| Vibration for Electronic Circuits | |
| JESD22-B104-C | Mechanical Shock for Electronic Circuits |
| JESD22- A106-B | Thermal Shock for Electronic Circuits |
TAPPI Standards | |
| TAPPI T 410 | Grammage of paper and paperboard |
| TAPPI T 411 | Thickness (Caliper) of Paper, Paperboard and Combined Board |
| TAPPI T 414 | Internal Tearing resistance of Paper (Elmendorf) |
| TAPPI T 460 | Air Resistance of Paper (Gurley) |
Tensile Properties of Paper & Paperboard (using constant rate of elongation apparatus) | |
| TAPPI T 810 | Bursting Strength of Corrugated and Solid Fiberboard |
| TAPPI T 811 | Edgewise compressive Strength of Corrugated fiberboard |
| TAPPI T 839 | Edgewise compressive Strength of Corrugated fiberboard |
沒有留言:
張貼留言